Menu Close

Digilent 410-370, Cora Z7: Zynq-7000 Single Core ARM/FPGA SoC Development

$180.00

The Digilent Cora Z7-07S is a compact Zynq-7000 SoC development board that pairs a 667 MHz single-core Arm Cortex-A9 processor with FPGA logic. It can boot embedded Linux from a microSD card and run independently with 512 MB of DDR3 memory and Gigabit Ethernet. A dual-channel analog-to-digital converter, two Pmod ports, and Arduino-compatible headers make it useful for sensor data acquisition and custom controller projects.

Description

Cora Z7: Zynq-7000 Single Core ARM/FPGA SoC Development Board

The Digilent Cora Z7 is a ready-to-use, low-cost, and easily embeddable development platform designed around the powerful Zynq-7000 All-Programmable System-on-Chip (APSoC) from Xilinx. The Zynq-7000 architecture tightly integrates a single core 667MHz ARM Cortex-A9 processor with a Xilinx 7-series FPGA. This pairing grants the ability to surround the processor with a unique set of software defined peripherals and controllers, tailored for the target application.

The Cora Z7’s wide array of hardware interfaces, from a 1Gbps Ethernet PHY to analog-to-digital converters and general-purpose input/output pins, make it an ideal platform for the development of a vast variety of embedded applications. The small form factor and mounting holes make the Cora Z7 ready to be used as one component of a larger solution. The on-board SD Card slot, Ethernet, and Power solution allow the Cora Z7 to operate independently of a host computer.

Features

ZYNQ Processor

  • 667MHz single-core Cortex-A9 processor
  • FPGA Programmable logic equivalent to Artix-7 FPGA
    • 3,600 Programmable logic slices
    • 60 DSP slices
    • 225 KB of block RAM
    • 14,400 Look-up Tables (LUTs)
    • 28,800 Flip-Flops
  • DDR3 memory controller with 8 DMA channels and 4 High Performance AXI3 Slave ports
  • High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO
  • Low-bandwidth peripheral controllers: SPI, UART, CAN, I2C
  • Dual-channel, 1 MSPS internal analog-digital converter
  • Programmable from JTAG and microSD card

Memory

  • 512MB DDR3 with 16-bit bus @ 1050Mbps
  • microSD slot

Power

  • Powered from USB or any 4.5V-5.5V external power source

USB and Ethernet

  • Gigabit Ethernet PHY with 48-bit globally unique EUI-48/64™ compatible identifier available on sticker
  • USB-JTAG programming circuitry
  • USB-UART bridge
  • USB OTG PHY (supports host only)

Push-buttons and LEDs

  • Two Push-buttons
  • Two RGB LEDs

Expansion Connectors

  • Two Pmod connectors
    • 16 Total FPGA I/O
  • Arduino/chipKIT Shield connector
    • Up to 49 Total FPGA Digital I/O
    • 6 Single-ended 0-3.3V Analog inputs to XADC
    • 8 Differential 0-1.0V Analog inputs to XADC
  • Unloaded expansion header
    • 12 additional FPGA Digital I/O

Resources & Downloads

Documentation

Tutorials

Example Projects

Additional Resources

Buy Online

Reviews

There are no reviews yet.

Be the first to review “Digilent 410-370, Cora Z7: Zynq-7000 Single Core ARM/FPGA SoC Development”

Your email address will not be published. Required fields are marked *