Description
Cora Z7: Zynq-7000 Single Core ARM/FPGA SoC Development Board
The Digilent Cora Z7 is a ready-to-use, low-cost, and easily embeddable development platform designed around the powerful Zynq-7000 All-Programmable System-on-Chip (APSoC) from Xilinx. The Zynq-7000 architecture tightly integrates a single core 667MHz ARM Cortex-A9 processor with a Xilinx 7-series FPGA. This pairing grants the ability to surround the processor with a unique set of software defined peripherals and controllers, tailored for the target application.
The Cora Z7’s wide array of hardware interfaces, from a 1Gbps Ethernet PHY to analog-to-digital converters and general-purpose input/output pins, make it an ideal platform for the development of a vast variety of embedded applications. The small form factor and mounting holes make the Cora Z7 ready to be used as one component of a larger solution. The on-board SD Card slot, Ethernet, and Power solution allow the Cora Z7 to operate independently of a host computer.
Features
ZYNQ Processor
- 667MHz single-core Cortex-A9 processor
- FPGA Programmable logic equivalent to Artix-7 FPGA
- 3,600 Programmable logic slices
- 60 DSP slices
- 225 KB of block RAM
- 14,400 Look-up Tables (LUTs)
- 28,800 Flip-Flops
- DDR3 memory controller with 8 DMA channels and 4 High Performance AXI3 Slave ports
- High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO
- Low-bandwidth peripheral controllers: SPI, UART, CAN, I2C
- Dual-channel, 1 MSPS internal analog-digital converter
- Programmable from JTAG and microSD card
Memory
- 512MB DDR3 with 16-bit bus @ 1050Mbps
- microSD slot
Power
- Powered from USB or any 4.5V-5.5V external power source
USB and Ethernet
- Gigabit Ethernet PHY with 48-bit globally unique EUI-48/64™ compatible identifier available on sticker
- USB-JTAG programming circuitry
- USB-UART bridge
- USB OTG PHY (supports host only)
Push-buttons and LEDs
- Two Push-buttons
- Two RGB LEDs
Expansion Connectors
- Two Pmod connectors
- 16 Total FPGA I/O
- Arduino/chipKIT Shield connector
- Up to 49 Total FPGA Digital I/O
- 6 Single-ended 0-3.3V Analog inputs to XADC
- 8 Differential 0-1.0V Analog inputs to XADC
- Unloaded expansion header
- 12 additional FPGA Digital I/O
Resources & Downloads
Documentation
- Cora Z7 Reference Manual (off-site)
- Cora Z7 Schematic (off-site)
- Master XDC Files (off-site)
- Petalinux Support for Digilent Boards (off-site)
- Xilinx Zynq Datasheet (off-site)
- Xilinx Zynq Technical Reference Manual (off-site)
Tutorials
- Getting Started with Digilent Pmod IPs (off-site)
- Getting Started with the Vivado IP Integrator (off-site)
- Getting Started with Vivado (off-site)
- Installing Vivado and Digilent Board Files (off-site)
Example Projects
- Cora Z7-07S Basic I/O Demo (off-site)
- Cora Z7-07S Pmod VGA Demo (off-site)
- Cora Z7-07S XADC Demo (off-site)
- Pmod I2S2 FPGA Volume Control Demo (off-site)
Additional Resources
- Estimating Pi with a Cora Z7 Running Linux (off-site)






Reviews
There are no reviews yet.